(no subject)
Aug. 16th, 2006 06:30 pm![[personal profile]](https://www.dreamwidth.org/img/silk/identity/user.png){kind=small}
afmetalsmithIt occurred to me today as I was carving wax in an intricate Celtic pattern for a casting, that it is very odd in some ways that waxwork is a metalsmithing skill! The process has pretty much nothing whatsoever to do with working with actual metal; it's just that since the goal is to make a metal thing out of the wax eventually, it's sort of an honorary metal skill.
I can see why there are those who specialize in it alone, though, some of whom don't work with metal at all!
I did a few rounds of depletion gilding on the cloisonne backings, after smoothing off the surface some more. Another pass or 2 should do it.
I also did some more work on the repair/reworking of my trillium pin/pendant. As I was fiddling with the central tube rivet to get the stone's "stem" to fit through it, the petals started to rotate again. So I acquiesced to the inevitable and drilled another, 1mm, hole very close to the central one- close enough that the stone will cover it when replaced- and riveted it a second time with a tiny piece of 18 ga. wire. Ha! Now just TRY to rotate! I was again grateful for my wonderful mini-stakes, because a couple of them made this process relatively painless, and it would not have been without them. I also see that I could if necessary glue the "stem" of the stone- it sticks out from the back of the cab setting- into the central tube rivet hole if necessary. This is a relief! I'm not sure that I have enough length to re-rivet it, plus of course hammering on the other end of something that has a large citrine cab on one end is a somewhat dangerous proposition!
Now that I know more or less what I'm doing, I can do the same work on the other pin, thereby fixing its problems and then being able to offer it for sale. I will be much happier sending it off when the petals and leaves aren't rotating like a pinwheel, and the pin is steel!
I have not yet begun the meanders around the features on my plique smiley; I'm planning on working on that, and on texturing the cloisonne metal, tomorrow while my student is here. Both are easily interruptable, which make them good candidates for that time.
Tonight J is planning on getting some new pictures of some of the work I want to put up on Etsy. Cool! I did add an enameled bat tie tack yesterday, but the photo I had was a bit low-res so it's grainy at full size. (The url is http://afmetalsmith.etsy.com, but so far there are only 2 things up. I'm looking to change that ASAP!)
I can see why there are those who specialize in it alone, though, some of whom don't work with metal at all!
I did a few rounds of depletion gilding on the cloisonne backings, after smoothing off the surface some more. Another pass or 2 should do it.
I also did some more work on the repair/reworking of my trillium pin/pendant. As I was fiddling with the central tube rivet to get the stone's "stem" to fit through it, the petals started to rotate again. So I acquiesced to the inevitable and drilled another, 1mm, hole very close to the central one- close enough that the stone will cover it when replaced- and riveted it a second time with a tiny piece of 18 ga. wire. Ha! Now just TRY to rotate! I was again grateful for my wonderful mini-stakes, because a couple of them made this process relatively painless, and it would not have been without them. I also see that I could if necessary glue the "stem" of the stone- it sticks out from the back of the cab setting- into the central tube rivet hole if necessary. This is a relief! I'm not sure that I have enough length to re-rivet it, plus of course hammering on the other end of something that has a large citrine cab on one end is a somewhat dangerous proposition!
Now that I know more or less what I'm doing, I can do the same work on the other pin, thereby fixing its problems and then being able to offer it for sale. I will be much happier sending it off when the petals and leaves aren't rotating like a pinwheel, and the pin is steel!
I have not yet begun the meanders around the features on my plique smiley; I'm planning on working on that, and on texturing the cloisonne metal, tomorrow while my student is here. Both are easily interruptable, which make them good candidates for that time.
Tonight J is planning on getting some new pictures of some of the work I want to put up on Etsy. Cool! I did add an enameled bat tie tack yesterday, but the photo I had was a bit low-res so it's grainy at full size. (The url is http://afmetalsmith.etsy.com, but so far there are only 2 things up. I'm looking to change that ASAP!)
